ایزولاتور 2 کانال اپتوکوپلری 2ch PC817 Optocoupler Isolation
ایزولاتور 2 کانال اپتوکوپلری 2ch PC817 Optocoupler Isolation، ایزولاتور و مبدل ولتاژ ورودی – خروجی اپتوکوپلری دو کانال، مجهز به اپتوکوپلر PC817 و چراغ LED برای هر کانال
- ولتاژ ورودی:3.6V to 24V
- ولتاژ خروجی:3.6V to 30V
- جریان خروجی:50mA
- فرکانس کاری:4KHz
- تعداد کانال:2
- اپتوکوپلر:PC817
- ابعاد:- + موارد بیشتر
این کالا در حال حاضر در انبار فروشگاه موجود ، آماده پردازش و ارسال است
49,000 تومان
موجود
ایزولاتور 2 کانال اپتوکوپلری 2ch PC817 Optocoupler Isolation
ایزولاتور اپتوکوپلری در بسیاری از مدارات استفاده می شود. با این مدار می توانید همزمان هم ورودی خروجی خود را از همدیگر ایزوله کنید و هم عمل تبدیل ولتاژ بین ورودی و خروجی را انجام دهید. این دو کار به صورت همزمان صورت میگیرد و از مزیت های اپتوکوپلر دوست داشتنی است.
با عملکرد ایزولاسیون میتوانید از آسیب های احتمالی وارده به مدارات الکترونیکی خود جلوگیری کنید و هم میتوانید با این مدار، مثلا مدارات 5 ولت میکروکنترلری را به مدارات تا 30 ولت نیز متصل نمایید. نقشه یک کانال از این ماژول در تصویر زیر نشان داده شده است.
Introduction:
This 2-channel PC817 optocoupler isolation module is used to convert input signals from one voltage level to an output of another voltage level.
The module will operate with input voltages in the range of 3.6V to 24V, and output voltages in the range of 3.6V to 30V, accommodating a wide range of voltages and applications. For example, you can monitor a 24V industrial or security sensor with a 5V (Arduino) or 3.3V-compatible device (ESP32, Raspberry Pi GPIO). It is ideal for use in noisy circuits where signal lines require electrical isolation.
The two channels are fully isolated from each other, so each module can handle two different input voltage signals and two different output voltage signals. The conversion for each channel is performed by a PC817 optocoupler. Each channel includes a jumper. If the jumper is installed, the ground (GND) connections of the input and output signals are connected. If you need fully isolated input and output signals, remove the jumper. The board has an LED for each channel. If the LED is on, the input signal is on.
If the input signal is off, the output signal is high. When the input signal turns on, triggering the optocoupler, the output signal goes low.
Specifications:
- Input voltage 3.6V to 24V
- Output voltage 3.6V to 30V
- Maximum Output (Emitter) Current: 50mA *
- Maximum Frequency: 4KHz
- Rise and Fall Times: 18us
- Channels: 2
Both channels are independent and can be used with different input and output voltages simultaneously - Input Pins:
- IN1 … IN2: +3.6V to 30 V
- G: Ground
- Output Pins:
- V1 … V2: Phototransistor collector pins
- G: Phototransistor emitter pins
NOTE: Optocouplers have a low output current. The maximum output current of the PC817 is 50 mA. As a result, you cannot connect high current components (such as motors, etc.) to the optocoupler output directly. You must use a transistor to supply the current of the output draws more than 50mA.
NOTE2: If it is a pulse signal, please note that the limit of 817 is 4KHZ or less Please do not use this module for control signals greater than 4KHZ, it will work Not working properly.
شما هم درباره این کالا پرسش ثبت کنید
امتیاز کاربران به: ایزولاتور 2 کانال اپتوکوپلری 2ch PC817 Optocoupler Isolation | (0 نفر )
هنوز امتیازی ثبت نشده است
شما هم میتوانید در مورد این کالا نظر دهید.