درایور ال سی دی LCD Driver PCB800099
درایور ال سی دی LCD Driver PCB800099، برد راه انداز نمایشگرهای LCD مدل PCB800099 توسط ورودی های AV, HDMI, VGA, LVDS و 50Pin TTL Interface که توسط آن می توانید بسیاری از نمایشگرهای مرسوم در بازار را راه اندازی نمایید.
این کالا در حال حاضر در انبار فروشگاه موجود ، آماده پردازش و ارسال است
588,000 تومان
موجود
درایور ال سی دی LCD DRIVER PCB800099
برد راه انداز نمایشگرهای LCD مدل PCB800099 توسط ورودی های AV, HDMI, VGA, LVDS و 50Pin TTL Interface که توسط آن می توانید بسیاری از نمایشگرهای مرسوم در بازار را راه اندازی نمایید. در تصویر زیر یک نمایشگر N070ICG-LD1 LED panel توسط این برد راه اندازی شده است.
برای مثال می توانید خروجی HMDI بردهای مینی کامپیوتر رسپبری پای را به یک نمایشگر AT070TN92 متصل کنید. حتی بعضی از مدلهای ال سی دی و ال ای دی لب تاپ نیز توسط این برد قابل راه اندازی می باشد.
( این نکته قابل ذکر است که firmware دستگاه برای نمایشگرهای 10.1 که در فروشگاه الکترونیک 724 موجود است سازگار است و باید برای نمایشگرهای TN92 و TN94 و .. که قابلیت پشتیبانی دارند firmware آن تغییر داده شود. تمامی Firmwareهای موجود در بخش دیتاشیت محصول قرار داده شده است که باید توسط پروگرامر SPI روی حافظه SPI FLASH نشان داده شده در تصویر برنامه ریزی شود.)
The driver board can
- 1-way VGA signal input
- 2 road AV signal input
- 1-way HDMI signal input and support of the IC is HDMI1.1
- 1-way reversing signal input
- support wide voltage input, and can work normally between 5V-24V
- the standard backlit 6PIN, interface, external pressure plate
- integrated LCD driver board LED backlight driver board road
- standard LVDS signal output, can support a single 6, 8 single, dual 6, 8, etc. LCD screen double standard LVDS signal, but only supports screen LCD supply of 3.3V
- standard key board interface, and supports dual-color LED display
- support General TTL signal output, Support AT070TN92,AT065TN14,AT080TN52,AT090TN12,AT090TN10 ,AT070TN90,AT070TN93 AT070TN94 so common 50 PIN TTL LCD interface
- The maximum output of the display driver board resolution, 1920X1080 over, 1440X900 display resolution when needed, as the work of the IC, increasing the heat sink to reduce the IC’s operating temperature)
- The IC, VGA YPBPR signal input section can be directly through the program
- The driver board can increase the remote control function (through software)
- Support for reversing control, and display on the AV2, reversing the voltage input 50V voltage support within
- The drive plate positioning holes for the four
CONFIGURATION & GENERAL PRECAUTIONS:
- Relative humidity: 80%.
- Storage temperature: -10~+60 °C.
- Operation temperature: 0~+40 °C.
- Protect the control board from static; it may cause damage to the IC.
- Disconnect the TV before the power supply of panel is connected correctly.
- Do not drop any metal on the control board when it is working.
- Do not push or pull the connector when the control board is working.
- Do not disassemble the module. If the surface or the control board is dirty, clean it with soft dry cloth.
- Can’t be pressed and distorted.
- Connect VGA cable/DVI cable/HDMI cable to controller board and PC/HDMI device then connect input power.
- The most important thing is to be sure the power supply is 12V, 4A
Note:
This controller board support Automatically Switch to AV2(Reversing View camera). Please connected ACC to 12V.
مشخصات درایور ال سی دی LCD Driver PCB800099
شما هم درباره این کالا پرسش ثبت کنید
اطلاعات فنی
درایور ال سی دی LCD Driver PCB800099
امتیاز کاربران به: درایور ال سی دی LCD Driver PCB800099 | (0 نفر )
هنوز امتیازی ثبت نشده است
شما هم میتوانید در مورد این کالا نظر دهید.